Exact: 1 in = 25.4 mm
MM to Inches Converter
To convert millimeters to inches, divide the length in millimeters by 25.4, because one inch is exactly 25.4 mm. The converter below gives the decimal result, the nearest fraction with its rounding error, feet plus inches and every calculation step.
in
- Feet + inches
10 mm / 25.4 mm/in = 0.393700787401575 in ≈ 25/64 in (Nearest 1/64) = 9.921875 mm Error = 9.922 − 10 = −0.078 mm
Every fraction, with its error
| Precision | Fraction | Error |
|---|---|---|
| 1/8 | 3/8 in | −0.475 mm |
| 1/16 | 3/8 in | −0.475 mm |
| 1/32 | 13/32 in | +0.319 mm |
| 1/64 | 25/64 in | −0.078 mm |
Error = fraction minus true value. A minus sign means the fraction is smaller.
Same length, other units
- Centimeters
- 1 cm
- Meters
- 0.01 m
- Feet
- 0.03281 ft
- Yards
- 0.01094 yd
- Thou (mil)
- 393.7 thou
- Points (pt)
- 28.346 pt
- Micrometers
- 10000 µm
Quick reference
- 1 mm
- 0.03937 in
- 1 cm
- 0.3937 in
- 1 in
- 25.4 mm
- 1 ft
- 304.8 mm
- 1 m
- 39.37 in
How to Convert Millimeters to Inches?
To convert millimeters to inches, divide the millimeter value by 25.4.
d(″) = d(mm) / 25.4
One millimeter is equal to 0.03937007874 inches:
1 mm = (1/25.4)″ = 0.03937007874″
The distance d in inches is the distance d in millimeters divided by 25.4:
Example #1
Convert 20 mm to inches.
20 mm = 20 mm / 25.4 mm/in = 0.7874 in
Example #2
Convert 50 mm to inches.
50 mm = 50 mm / 25.4 mm/in = 1.9685 in
How Many Inches Are in a Millimeter?
0.03937in
One millimeter is equal to 0.03937 inches:
1 mm = 1 mm / 25.4 mm/in = 0.03937 in
How Many Millimeters Are in an Inch?
25.4mm
One inch is equal to 25.4 millimeters:
1 in = 25.4 mm/in × 1 in = 25.4 mm
This figure is a definition rather than a measurement. It was fixed by the International Yard and Pound Agreement, which took effect on 1 July 1959 and defined the international yard as exactly 0.9144 meters. Everything else follows from that: the foot became exactly 0.3048 meters and the inch exactly 25.4 mm. The number carries no uncertainty and will not change.
What Is 10 mm in Inches?
10 mm is 0.3937 inches, or 25/64 inch as the nearest fraction.
Divide 10 millimeters by 25.4 to get inches:
10 mm = 10 mm / 25.4 mm/in = 0.3937 in
Rounded to the nearest 1/64, that is 25/64 inch, which is 0.390625 in or 9.922 mm. The fraction is 0.078 mm smaller than the true value.
MM to Inches Conversion Chart
Fraction inches are rounded to 1/64 resolution.
| Millimeters (mm) | Inches (decimal) | Inches (fraction) |
|---|---|---|
| 0.01 mm | 0.0004 ″ | 0 ″ |
| 0.1 mm | 0.0039 ″ | 0 ″ |
| 0.5 mm | 0.0197 ″ | 1/64 ″ |
| 1 mm | 0.0394 ″ | 3/64 ″ |
| 2 mm | 0.0787 ″ | 5/64 ″ |
| 3 mm | 0.1181 ″ | 1/8 ″ |
| 4 mm | 0.1575 ″ | 5/32 ″ |
| 5 mm | 0.1969 ″ | 13/64 ″ |
| 6 mm | 0.2362 ″ | 15/64 ″ |
| 7 mm | 0.2756 ″ | 9/32 ″ |
| 8 mm | 0.3150 ″ | 5/16 ″ |
| 9 mm | 0.3543 ″ | 23/64 ″ |
| 10 mm | 0.3937 ″ | 25/64 ″ |
| 12 mm | 0.4724 ″ | 15/32 ″ |
| 15 mm | 0.5906 ″ | 19/32 ″ |
| Millimeters (mm) | Inches (decimal) | Inches (fraction) |
|---|---|---|
| 20 mm | 0.7874 ″ | 25/32 ″ |
| 30 mm | 1.1811 ″ | 1 3/16 ″ |
| 40 mm | 1.5748 ″ | 1 37/64 ″ |
| 50 mm | 1.9685 ″ | 1 31/32 ″ |
| 60 mm | 2.3622 ″ | 2 23/64 ″ |
| 70 mm | 2.7559 ″ | 2 3/4 ″ |
| 80 mm | 3.1496 ″ | 3 5/32 ″ |
| 90 mm | 3.5433 ″ | 3 35/64 ″ |
| 100 mm | 3.9370 ″ | 3 15/16 ″ |
| 150 mm | 5.9055 ″ | 5 29/32 ″ |
| 200 mm | 7.8740 ″ | 7 7/8 ″ |
| 250 mm | 9.8425 ″ | 9 27/32 ″ |
| 300 mm | 11.8110 ″ | 11 13/16 ″ |
| 500 mm | 19.6850 ″ | 19 11/16 ″ |
| 1000 mm | 39.3701 ″ | 39 3/8 ″ |
Why Is the Inch Fraction Never Exact?
An inch fraction is rarely exact because metric units divide by ten while inch fractions divide by two, so most millimeter values fall between two fraction marks.
Every other converter stops at the table above. It is worth going one step further, because the fraction column hides something.
Metric divides by ten and imperial divides by two, so a millimeter value almost never lands on a fraction. The fraction you are given is the closest sixty fourth and the gap between it and the true value changes from row to row.
| Millimeters | True decimal | Nearest 1/64 | Fraction in mm | Error |
|---|---|---|---|---|
| 1 mm | 0.0394 ″ | 3/64 ″ | 1.191 mm | +0.191 mm |
| 5 mm | 0.1969 ″ | 13/64 ″ | 5.159 mm | +0.159 mm |
| 10 mm | 0.3937 ″ | 25/64 ″ | 9.922 mm | −0.078 mm |
| 20 mm | 0.7874 ″ | 25/32 ″ | 19.844 mm | −0.156 mm |
| 25 mm | 0.9843 ″ | 63/64 ″ | 25.003 mm | +0.003 mm |
| 50 mm | 1.9685 ″ | 1 31/32 ″ | 50.006 mm | +0.006 mm |
| 100 mm | 3.9370 ″ | 3 15/16 ″ | 100.012 mm | +0.012 mm |
Error = fraction minus true value. A minus sign means the fraction is smaller.
Notice that 25 mm and 50 mm sit almost exactly on a fraction while 1 mm and 20 mm are well off one. There is no pattern you can rely on, which is why the converter above reports the error with every result instead of leaving you to assume the fraction is correct.
How Many Decimal Places Do You Need?
Keep one decimal place for rough carpentry, two for joinery and three for machining, and never round more coarsely than the tolerance on the drawing.
Rounding too hard ruins a part. Carrying ten decimals wastes your time.
-
Rough carpentry, framing and general construction
one decimal place or the nearest 1/16. Timber moves more than that with humidity.
-
Furniture, cabinetry and joinery
two decimal places or the nearest 1/32.
-
Metalwork and machining
three decimal places, minimum. Machinists work in thousandths of an inch and one thou is 0.0254 mm.
-
Engineering drawings
follow the tolerance printed on the drawing, not a general rule.
The single rule that covers all of it: never round a converted value more coarsely than the tolerance you were given. If the drawing says plus or minus 0.05 mm and you round to the nearest 1/64, your rounding error can already exceed the tolerance.
What Is a Millimeter?
A millimeter (mm) is a unit of length in the metric system.
- One millimeter is 1/1000 of a meter (m).
- One millimeter is 1/10 of a centimeter (cm).
- One millimeter is 1/25.4 of an inch (in).
The millimeter is the working unit for engineering drawings, machining, electronics and construction detailing, because it describes small differences without needing decimals.
What Is an Inch?
An inch (in or ″) is a unit of length in the US customary and imperial systems.
- One inch is 1/12 of a foot (ft).
- One inch is 1/36 of a yard (yd).
- One inch is exactly 25.4 millimeters (mm).
Unlike the millimeter, the inch is normally divided in halves rather than tenths, which is why measurements appear as 1/2, 1/4, 1/8, 1/16, 1/32 and 1/64 rather than as decimals.
What Is the Difference Between Millimeters, Centimeters and Inches?
A millimeter is 1/10 of a centimeter and 1/25.4 of an inch, so one inch equals 2.54 cm or 25.4 mm.
| Unit | In millimeters | In inches |
|---|---|---|
| 1 mm | 1 mm | 0.0394 in |
| 1 cm | 10 mm | 0.3937 in |
| 1 in | 25.4 mm | 1 in |
| 1 ft | 304.8 mm | 12 in |
| 1 yd | 914.4 mm | 36 in |
For mental arithmetic: an inch is a little under two and a half centimeters and a centimeter is a little under four tenths of an inch.
Where Do Millimeters and Inches Collide?
Millimeters and inches collide in sockets and bolts, drill bits, lumber, paper sizes, photography, displays and pipe sizes.
These are the situations that send people to a converter and the ones where getting it wrong costs something.
-
Sockets and bolts
Metric and imperial sizes are close enough to be dangerous. A 13 mm socket nearly fits a 1/2 inch bolt head and will round the corners off it. 1/2 inch is 12.7 mm, so the socket is 0.3 mm loose.
-
Drill bits
A 6 mm bit is 0.2362 in, nearest to 15/64. The common 1/4 inch bit is 6.35 mm, which is 0.35 mm larger. Picking by eye gives you a hole that is loose or tight.
-
Lumber
A nominal 2x4 actually measures 1.5 by 3.5 inches, which is 38.1 by 88.9 mm. Neither figure matches the name.
-
Paper
A4 is 210 by 297 mm, which is 8.2677 by 11.6929 inches. US Letter is 8.5 by 11 inches or 215.9 by 279.4 mm. A4 is narrower and taller, which is why printing one on the other crops or shrinks the page.
-
Photography
35 mm film is named for its width, which is 1.3780 inches. Lens threads are metric while tripod mounts are imperial.
-
Displays
Screen sizes are quoted as a diagonal in inches while the panel and bezel dimensions are specified in millimeters.
-
Pipe
The worst offender, because many imperial pipe sizes are nominal names rather than real measurements. Converting the label does not give you the actual diameter.
Frequently Asked Questions
How many millimeters are in an inch?
Exactly 25.4. It is a definition rather than a measurement, so the figure carries no uncertainty and never changes.
How do I convert mm to inches?
Divide the millimeter value by 25.4. For example, 50 / 25.4 = 1.9685 inches.
What is 10 mm in inches?
0.3937 inches or 25/64 as the nearest fraction. The fraction is 0.078 mm smaller than the true value.
What is 1 mm in inches?
0.0394 inches, nearest to 3/64. That fraction is 0.191 mm larger than a true millimeter, which is the biggest rounding error anywhere in the common table.
What is 100 mm in inches?
3.9370 inches, which is almost exactly 3 15/16 and sits within 0.012 mm of it.
Is 25 mm the same as 1 inch?
No. One inch is 25.4 mm, so 25 mm is 0.9843 inches, about 1.6 percent short. The approximation is fine for a rough estimate and not for anything that has to fit.
How do I convert mm to a fraction of an inch?
Divide by 25.4 for the decimal, then round to the nearest 1/16, 1/32 or 1/64 depending on the precision you need. The converter above shows the fraction and the error together.
Why is an inch exactly 25.4 mm?
The United States, the United Kingdom, Canada, Australia, New Zealand and South Africa signed the International Yard and Pound Agreement on 1 July 1959, defining the international yard as exactly 0.9144 meters. That fixed the inch at exactly 25.4 mm in all six countries.
How many decimal places should I keep?
One for rough carpentry, two for joinery, three for machining. Never round more coarsely than the tolerance you were given.
How do I convert mm to feet?
Divide by 304.8, since a foot is exactly 304.8 mm. Or divide by 25.4 for inches and then by 12.
What is a thou or a mil?
One thousandth of an inch, which is 0.0254 mm. It is the standard unit of precision in machining and the reason three decimal places is normal there.
Why does my converted value not match the mark on my ruler?
Because metric divides by ten and imperial by two, so most millimeter values fall between two fractions rather than on one. The error figure tells you how far off the nearest mark is.
Is the conversion the same in the UK and the US?
Yes. Both have used the same definition since 1959.
Can I use 25 instead of 25.4 for quick mental math?
For a rough figure, yes. It makes your answer about 1.6 percent too large, so never use it for a part that has to fit.
What is 0.1 mm in inches?
0.0039 inches, which is about four thou. It rounds to zero at 1/64 resolution, which is why fine work is quoted in decimals rather than fractions.
How accurate is this converter?
It divides by the exact figure of 25.4 and reports the decimal, the nearest fraction and the rounding error, so you can see exactly what you give up when you round.